How to Fix a Traeger Auger Jammed Solid From Wet Pellets
Clear a Traeger auger jammed solid from Ontario humidity by unbolting the motor, tapping out the hardened sawdust plug, and cleaning the tube safely.
To fix a Traeger auger jammed solid, unplug the grill, unbolt the auger motor under the hopper, and twist the spiral shaft backward with locking pliers while vacuuming out the hardened sawdust plug.
If you live near the water in Whitby, Port Hope, or up on Pigeon Lake near Bobcaygeon, Ontario humidity is your pellet grill's worst enemy. Wood pellets are nothing more than kiln-dried sawdust pressed together under high heat. When damp lake air sneaks up the grease chute or sits in your hopper during a rainy week, those pellets swell to three times their size and dry into a grey block that feels like poured concrete.
Stop Pressing the Prime Button When You Hear Clicking
Turn the grill off immediately if the auger stops turning or makes a rhythmic clicking or humming sound from beneath the hopper.
The auger motor turns at roughly 1.6 to 2 revolutions per minute using a stack of small plastic and metal reduction gears inside a sealed gearbox. When the spiral shaft is cemented into the tube by swollen sawdust, running the "Clear Auger" or "Prime" menu option puts all that torque directly onto the plastic drive teeth. Within two or three cycles, the gears strip out or the sheer pin snaps, turning a free 45-minute clean-out into a motor replacement.
Watch for these warning signs before a total lockup happens:
- The grill fails to ignite within 15 minutes and displays a low-temperature alarm.
- Whole pellets in the bottom of the hopper look furry, dull, or crumbled into loose sawdust.
- You hear a dull thudding noise every 3 to 5 seconds from under the pellet box.
- Temperature swings wildly by 25°C (45°F) or more, which looks a lot like when you need to fix a Traeger temperature fluctuating from ash buildup.
Empty the Barrel and Drop the Hopper Skirt First
Unplug the power cord from the wall outlet and strip out all internal barrel components before touching the auger assembly.
Never reach into the firepot or under the hopper while the grill is plugged in, even if the screen is dark. And if you wait for your smoker to clear by firing up a propane side burner or backup gas grill nearby, check those rubber gas hoses for cracks or rodent teeth marks first—if you ever smell gas or spot a damaged line, shut the tank valve off immediately and call a TSSA-registered gas technician in Ontario.
- Unplug the power cord from the deck outlet.
- Lift out the cooking grates, grease drip tray, and steel heat baffle to expose the central firepot in the bottom of the barrel.
- Scrape any cold grease off the grates with a wooden paddle or nylon pad while they are out; never use a wire bristle brush on food surfaces, and never spray oven cleaner on painted or porcelain grill parts.
- Open the rear hopper trapdoor and drain all dry pellets into a 20-litre bucket, then scoop out the damp, crusty layer at the very bottom with a plastic cup and a shop vac.
- Remove the 4 to 6 Phillips screws (or 6-millimetre hex bolts on newer D2 direct-drive units) holding the bottom metal access cover under the pellet box, and lower the panel gently so you do not yank the controller wires.
Unbolt the Motor and Work the Auger Out Backward
Disconnect the auger motor from the shaft and break up the concrete sawdust plug from both ends using a flathead screwdriver and a shop vac.
Do not hammer on the end of the auger shaft from inside the firepot, and never pour boiling water down the auger tube. Water makes the compressed wood swell even harder inside the steel pipe and rusts the bare metal shaft.
- Unplug the plastic molex wire connector linking the auger motor to the main wiring harness.
- Use a 7-millimetre socket or small wrench and a Phillips screwdriver to remove the sheer pin bolt (or unscrew the brass auger bushing on newer brush-less models) that holds the motor onto the auger shaft, then slide the motor straight off.
- Shine a flashlight into the firepot and use a 25-centimetre (10-inch) flathead screwdriver to chip away the hard crust of swollen wood at the tip of the auger, sucking the dust out with a shop vac every 30 seconds.
- Clamp a pair of 25-centimetre locking pliers onto the square or round motor-end of the auger shaft under the hopper.
- Rock the pliers clockwise and counter-clockwise in 2-centimetre increments until the crust breaks loose, then twist counter-clockwise while pulling firmly to corkscrew the auger out of the tube.
- Push a 3-centimetre (1.25-inch) nylon bottle brush or a wooden dowel wrapped in a dry cloth through the empty auger tube to knock out any caked-on sawdust rings, and vacuum the tube completely bare.
- Sand any orange surface rust off the steel auger flighting with a sheet of 220-grit sandpaper, wipe it dry, slide it back into the tube, and bolt the motor and access cover back in place.
Prevent Damp Pellet Jams in Ontario Weather
Drain the hopper and clear the auger tube whenever your grill will sit unused for more than 5 days in humid weather or over the winter.
Spring start-up and late-autumn rain in places like Ajax, Uxbridge, and Lindsay bring heavy overnight condensation. Even with a heavy canvas cover over the grill, moisture wicks into the wood pellets waiting inside the metal tube. Emptying the system takes less than 5 minutes and also helps keep mice out of a pellet grill at the cottage when you close up for the week.
- Store unused pellets indoors in sealed 20-litre plastic pails with rubber gasket lids, never in the original paper or perforated plastic bags on a damp garage floor.
- Sift the bottom of every pellet bag through a kitchen colander before pouring it into the hopper so loose sawdust does not pack into the auger tube.
- Run the auger clear cycle for 2 minutes after your final weekend cook whenever rain or high humidity is in the forecast.
Know When to Call a Professional Grill Technician
Call an experienced grill technician if the auger shaft will not budge with locking pliers, the nylon auger bushing is cracked, or the motor gears grind when tested off the shaft.
Sometimes a pellet jam sits through an entire Ontario winter, rusting the carbon-steel auger directly to the inside wall of the auger tube. Putting a long pipe wrench on the shaft can twist the metal spiral out of shape or crack the spot welds holding the hopper to the barrel. Look at the white plastic ring (or brass bushing) where the auger exits the tube—if it is melted or split in half, the auger will bind against the steel wall every time it heats up.
When you are tired of fighting baked-on carbon, clogged firepots, and seized parts, our mobile technicians clean and restore pellet, gas, and charcoal grills across our service locations in Durham Region, Kawartha Lakes, and Northumberland. As of 2026-11, our BBQ cleaning services are $190 for Standard (1–2 burners), $250 for Select (3–4 burners), $340 for Estate (5–6 burners), and quote on request for Premium built-in or luxury grills.
If your smoker or gas grill needs a full deep clean and inspection in your own driveway, you can book a cleaning online in about two minutes.
Your questions
Can I pour water into a jammed pellet grill auger to dissolve the pellets?
No, pouring water into a jammed auger tube makes the compressed wood sawdust swell even tighter inside the metal pipe and causes the bare steel auger to rust in place. Always clear a swollen pellet jam dry by chipping away the hardened plug with a long flathead screwdriver, vacuuming out the loose crumbs with a shop vac, and twisting the auger out with locking pliers.
Why is my Traeger auger clicking and not turning?
A clicking sound from underneath the pellet hopper means the auger shaft is jammed solid by wet pellets or a foreign object, causing the plastic reduction gears inside the auger motor to slip or strip. Turn the grill off right away so you do not burn out the motor windings, then remove the motor and clear the obstruction from the auger tube.
How long can you leave pellets in a Traeger hopper in Ontario?
During dry summer weather when you cook two or three times a week, pellets can stay in the hopper for up to 2 weeks if the grill is kept under a waterproof cover. If heavy rain, high humidity, or winter storage is coming—or if you are leaving a cottage grill unattended for more than 5 days—empty the hopper and run the auger clear cycle completely.
