Fix a Traeger Temperature Fluctuating From Ash Buildup
Is your Traeger temperature fluctuating wildly? Hidden ash inside the firepot and on the RTD probe is usually to blame. Follow our clean-out steps.
A Traeger temperature fluctuating by 25 to 50 degrees Fahrenheit is almost always caused by compacted ash in the firepot and baked-on soot on the RTD sensor. A 20-minute vacuum and probe wipe fixes the problem without buying new parts.
Firepot ash and dirty sensors trick the controller
Ash is a natural insulator, much like the fibreglass in your attic walls. Every hour you smoke ribs or brisket, the auger pushes hardwood pellets into the bottom of the steel firepot. Small air holes around the firepot let the induction fan blow oxygen onto the hot rod to keep a steady, clean flame.
After 15 to 20 hours of cooking, fine grey ash packs down at the bottom of that pot and blocks the lower air holes. When the fire suffocates, the grill cools down below your set mark. The silver RTD temperature probe bolted inside the barrel notices the drop and tells the auger to feed more pellets.
Because the air is blocked, those fresh pellets pile up on top of the smouldering ash instead of catching right away. Once the pile finally ignites all at once, the temperature spikes 40 degrees past your target. If that spike gets completely out of hand, you may also end up decoding the Traeger high temp error ER01 on your screen.
Meanwhile, if the RTD probe itself is coated in sticky brown creosote and flying ash, it reacts two or three minutes too late to every change inside the barrel. The sensor tells the auger to stop feeding pellets long after the barrel is already too hot, creating a constant roller coaster of high and low swings.
Vacuum the firepot and wipe the probe in six steps
Pulling the internal parts out to reach the firepot takes about 20 minutes and requires no tools other than a shop vacuum and a scrub pad. Every statement in this checklist starts with a completely cold, unplugged grill.
- Unplug the power cord from the wall and check with your bare hand over the grates to be sure the firepot has been cold for at least two hours.
- Lift out the porcelain or stainless cooking grates, the angled grease drip tray, and the heavy steel heat baffle sitting directly over the firepot. Set them on cardboard so you do not stain your deck. If your grates have baked-on food, brush them with a wooden scraper or coiled stainless spring brush; never use a wire bristle brush on food surfaces, as loose metal bristles can stick to your grill and end up in food.
- Place the nozzle of a dedicated shop vacuum or ash vacuum directly inside the cylindrical steel firepot and vacuum for 60 seconds, scraping the nozzle gently around the bottom until you can clearly see the shiny metal floor, the small finger-sized hot rod at the base, and every air hole around the wall.
- Vacuum the entire bottom floor of the barrel around the firepot for two to three minutes to pull up stray ash, charred pellet dust, and spilled crumbs that the fan could blow back onto your sensor.
- Locate the thin, four-inch vertical metal rod on the left inner wall of the barrel (the RTD temperature probe). Dampen a nylon non-scratch dish pad with warm water and 5 mL (one teaspoon) of mild dish soap, then gently pinch and wipe the metal rod for 30 seconds until the silver steel shines. Never use oven cleaner on painted or porcelain parts or near the internal sensors, and never bend or pull on the probe wire.
- Dry the probe with a paper towel, reinstall the heat baffle, drip tray, and grates in reverse order, and plug the grill back in.
Ontario humidity turns dry wood ash into cement
Wait too long between vacuuming sessions in southern and central Ontario, and a simple vacuum job turns into a scraping chore. Wood ash pulls moisture straight out of the air. Whether you are grilling near the lake in Ajax or closing up a weekend property in Bobcaygeon, summer humidity and damp autumn nights turn fluffy grey ash into a hard, damp crust inside the firepot.
That damp paste holds moisture directly against bare steel, speeding up rust on your heat baffle and firepot walls. It also cakes around the hot rod, forcing the igniter to work twice as hard during startup. In late fall and early spring, when evenings drop below freezing, damp pellets left in the auger tube can also swell and crumble into sawdust, adding three times the normal dust directly into the pot.
Follow this schedule to keep the airflow clear:
- Vacuum the firepot and barrel floor after every 15 to 20 hours of cook time, or after every full 20-pound bag of pellets you burn.
- Vacuum after every single long, low-and-slow smoke (such as a 12-hour pork shoulder or brisket) before starting a high-heat sear.
- Wipe the RTD probe with warm soapy water every second time you vacuum the firepot.
- Empty the hopper and run the auger dry before winter storage so pellets do not swell in the damp cold.
Warning signs that mean you need a deep clean or repair
Sometimes a quick shop-vac session is not enough to stabilize your heat. When grease mixes with floating wood ash underneath the drip tray and inside the chimney cap, it restricts exhaust airflow and creates a grease fire hazard. Watch for these signs that your pellet grill needs more than a five-minute vacuum:
- Thick black flakes peeling off the inside of the lid (baked-on creosote and grease vapour, not peeling paint).
- Yellow or orange roaring flames shooting up around the edges of the drip tray when you raise the heat above 350 degrees Fahrenheit.
- White, acrid smoke pouring out of the pellet hopper lid instead of the chimney, which means ash and sawdust are causing burn-back up the auger tube.
- Temperature readings on the screen that jump by 50 degrees in two seconds even when the lid is shut and the probe is clean, pointing to a failing RTD wire.
If you own a dual-fuel setup or a traditional propane grill alongside your smoker and ever notice gas smells, leaks, or damaged hoses, turn off the gas immediately and call a licensed gas technician (TSSA-registered in Ontario). For pellet grills, never splice damaged high-voltage cords yourself; unplug the unit if wires are chewed by mice over the winter.
While vacuuming dry ash is an easy job between cooks, scraping polymerized grease, degreasing the underside of the lid, and clearing encrusted internal chutes is messy, heavy work. You can read more about signs your grill needs a deep clean if your smoker has gone a full season or two without a teardown. If you would rather skip the soot and grease scraping altogether, feel free to book a cleaning.
Your questions
How often should I vacuum out my Traeger firepot?
Vacuum your Traeger firepot after every 15 to 20 hours of cooking, after burning through one 20-pound bag of pellets, or right after any single cook that lasts longer than eight hours. Keeping the air holes in the firepot clear prevents flameouts and temperature swings.
Can I clean a Traeger RTD probe with steel wool?
No, do not use steel wool or metal scrapers on the RTD temperature probe because scratching the thin stainless steel casing can damage the internal sensor. Use a soft nylon dish pad with warm water and mild dish soap, or a rag dampened with rubbing alcohol, to wipe away soot and grease.
Why is my Traeger running 30 degrees hotter than the set temperature?
A Traeger running 30 degrees too hot usually has soot buildup insulating the RTD probe, causing it to read cooler than the actual barrel temperature and feed too many pellets. It can also happen if the chimney cap is screwed down too low, trapping heat inside the drum instead of letting exhaust escape.

